Center pivot type of irrigation also known as waterwheel method of irrigating and basically involves a special type of a machine which transfers water in some circular kind of patterns so as to cover the entire portion of land being irrigated. The area to be covered by center pivot irrigation system is mostly dependent on the size of the machine used.
This method of watering crops is usually viewed to use lesser amounts of water when compared to the surface methods together with the furrow irrigation. Due to this water conservation technique the farmer is therefore saved some significant amount of expenditures. This method is also viewed to reduce costs of labor when compared to the ground techniques of irrigation.
When compared to the furrow systems a farmer is also saved some huge amounts of labor costs. The ground irrigation methods are actually labor intensive method as there are some which demand digging of ground water channels. This pivot systems usually reduce the tillage of soil while decreasing the amounts of water runoffs at a greater percentage.
One of the main advantages of this method is that it can irrigate a huge portion of land but the surface of the topography must be flat. In all irrigation methods the one type of irrigation which is viewed to surpass the waterwheel especially with regards to water loss is the drip method. Farmers with large farms or ranches, this kind of watering system is ideal for them.
Additionally this method of watering crops gives a farmer a chance to determine the amount of water which plants can be able to receive and the time which the plants should be watered. This method also ensures that there is minimal wastage of water. In most of dry areas both evaporation of water together with drift of wind tends to cause a greater loss of water to planted crops.
The two systems are however regarded to as low pressure systems. The middle pivot system of irrigation is also essential since a farmer can be able to apply his chemicals with a lot of ease. There are also some few disadvantages which are associated with the method of watering crops.
The drip method of watering crops not unless the tube gets damaged, the run off as well as puddling is not a concern. Soil erosion is basically the greatest concern especially when it comes to the furrow method of watering crops. It has been viewed that the pressure which is required to run the center pivot machine is always huge when compared to the drip method of irrigation although these two systems are considered to be low pressure systems.
The drip irrigating method usually makes use of pipes which are buried in the soil and they only last for a period of six to eight years. Waters mains especially in the drip type of irrigation tend to however remain very intact for a subsequent use.
This method of watering crops is usually viewed to use lesser amounts of water when compared to the surface methods together with the furrow irrigation. Due to this water conservation technique the farmer is therefore saved some significant amount of expenditures. This method is also viewed to reduce costs of labor when compared to the ground techniques of irrigation.
When compared to the furrow systems a farmer is also saved some huge amounts of labor costs. The ground irrigation methods are actually labor intensive method as there are some which demand digging of ground water channels. This pivot systems usually reduce the tillage of soil while decreasing the amounts of water runoffs at a greater percentage.
One of the main advantages of this method is that it can irrigate a huge portion of land but the surface of the topography must be flat. In all irrigation methods the one type of irrigation which is viewed to surpass the waterwheel especially with regards to water loss is the drip method. Farmers with large farms or ranches, this kind of watering system is ideal for them.
Additionally this method of watering crops gives a farmer a chance to determine the amount of water which plants can be able to receive and the time which the plants should be watered. This method also ensures that there is minimal wastage of water. In most of dry areas both evaporation of water together with drift of wind tends to cause a greater loss of water to planted crops.
The two systems are however regarded to as low pressure systems. The middle pivot system of irrigation is also essential since a farmer can be able to apply his chemicals with a lot of ease. There are also some few disadvantages which are associated with the method of watering crops.
The drip method of watering crops not unless the tube gets damaged, the run off as well as puddling is not a concern. Soil erosion is basically the greatest concern especially when it comes to the furrow method of watering crops. It has been viewed that the pressure which is required to run the center pivot machine is always huge when compared to the drip method of irrigation although these two systems are considered to be low pressure systems.
The drip irrigating method usually makes use of pipes which are buried in the soil and they only last for a period of six to eight years. Waters mains especially in the drip type of irrigation tend to however remain very intact for a subsequent use.
About the Author:
You can find a summary of the advantages you get when you install a center pivot irrigation system at http://www.triirrigate.com/services right now.
0 komentar:
Posting Komentar